These groups increase hydrophilicity and chemical reactivity but reduce electrical conductivity compared with pure graphene.
Synthesis: the classic method is Hummers’ method (oxidation of graphite with strong oxidizers, e.g., KMnO₄ in H₂SO₄), followed by exfoliation into individual sheets; modifications and alternatives exist to control the degree of oxidation and defect density.
Key properties: thickness — ~1 atom; solubility — good in water; electrical conductivity — low; mechanical strength — high, but lower than graphene; chemical reactivity — high (due to oxygen groups).
Applications and Commercial Context
Main application areas: water purification membranes (nanofiltration, metal removal), energy storage (batteries, supercapacitors), biomedicine (drug carriers, biosensors), composites (polymer reinforcement), and electronics (flexible sensors). These areas are actively developing and have varying sensitivity to GO purity and form.
Price and market factors: the price range depends on purity, form (powder/dispersion), volume, and manufacturer: ~USD 450–650/kg for industrial-grade GO (99%, etc.) and ~USD 1,500/kg for high-purity laboratory batches (example: TECHINSTRO).
Comparison of GO and Reduced GO (rGO) — Brief Table
Sources: .
Risks, Limitations, and Recommendations
Quality and reproducibility: degree of oxidation and defects strongly affect properties; request analytical data (XPS, Raman, TEM) from the supplier.
Safety and regulation: biomedical applications require biocompatibility and toxicity testing.
Economics: for large-scale applications, compare cost per functional unit (e.g., per m² of membrane or per unit of battery capacity), not just price per kg.
Recommendation: if you need help selecting suppliers, defining specifications (purity, sheet size, form), or comparing GO vs. rGO for a specific application, state the goal and a supplier list with a techno-economic comparison can be prepared.
Structure, synthesis and characterization
Structure. GO is a graphene sheet bearing functional groups: epoxy (–O–), hydroxyl (–OH), carboxyl (–COOH); these groups make the material hydrophilic and reactive but reduce conductivity compared with graphene.
Synthesis. The classic route is the Hummers method and its modifications: oxidation of graphite with strong oxidizers (KMnO₄ in H₂SO₄), followed by exfoliation and purification; modifications aim to control the degree of oxidation, sheet size, and reduce by-products.
Characterization. Mandatory methods: XPS (degree of oxidation), Raman (structural defects), TEM/AFM (size/thickness), TGA (thermal stability), FTIR (functional groups).
Properties and Applications
Key properties: thickness ~1 atom; solubility/dispersibility in water — high; electrical conductivity — low; high chemical reactivity and adhesion to polymers/ions.
Applications: water purification membranes (nanofiltration, metal removal), electrode and supercapacitor enhancement, drug carriers and biosensors, composite reinforcement, flexible electronics. Each application requires different GO parameters (purity, sheet size, degree of reduction).
Comparison of GO vs. rGO
Checklist for Requesting and Accepting a Batch of Graphene Oxide (GO)
Below is a compact, practical checklist that can be used as a template for requesting quotes, drafting technical specifications, and accepting a batch.
1. Technical Characteristics and Analytics
C/O ratio (XPS) — specify the required range; request the XPS spectrum.
Functional groups (FTIR) — presence of epoxy, hydroxyl, and carboxyl peaks.
Raman — spectrum with ID/IG ratio and comments on defect density.
Thickness and number of layers (AFM/TEM) — average thickness, confirmation of single-atom layers.
Lateral sheet size (TEM/SEM) — average and size distribution.
Zeta potential — dispersion stability at a given pH.
Dispersion concentration — g/L or % (if supplied as a suspension).
Moisture content (TGA or Karl Fischer) — % water.
Residual metals (ICP-MS) — Mn, K, Fe, etc.; threshold limits.
Ash/inorganics — % residue after calcination.
Surface area (BET) — m²/g, if relevant.
Thermal stability (TGA) — decomposition profile.
Conductivity/resistivity — if relevant to the application.
Particle/agglomerate size (DLS for dispersions) — volume distribution.
2. Documentation and Supporting Data
Certificate of Analysis (CoA) — for each batch, with results of all tests.
Batch/Lot number — batch identification.
Raw material traceability — graphite source and synthesis description.
Synthesis method — specify (Hummers, modified Hummers, etc.).
Measurement protocols — methods and instruments (XPS, Raman, TEM, etc.).
SDS/MSDS — material safety data sheet.
Shelf life and storage conditions — recommended temperature and humidity.
Packaging and labeling — container material, sealing, net weight.
Test sample — request a trial batch/sample.
3. Biocompatibility and Safety (if applicable)
Endotoxin/LAL test — for biomedical applications.
In vitro cytotoxicity — basic cell-based tests (if required).
Toxicological data — inhalation/dermal risk, PPE recommendations.
Regulatory certificates — compliance with standards (if required).
4. Commercial and Logistics Terms
Supply form — powder or dispersion (solvent, concentration).
MOQ and lead time — minimum order quantity and production/delivery times.
Price per kg — with delivery terms specified (EXW, FOB, DDP).
Payment terms — prepayment, letter of credit, etc.
Warranties and returns — policy for quality non-conformance.
Trial batch — option to order a small trial batch.
5. Acceptance Criteria and Testing Frequency
Batch acceptance — CoA plus independent sample verification (by agreement).
Rejection criteria — acceptable deviations for key parameters (C/O ±x%, ID/IG ±y, moisture ≤ z%).
Testing frequency — every batch; for recurring supply, spot-check 1 in N.
6. Recommendations for Supplier Requests (Brief)
Request the full CoA and raw data (spectra, micrographs).
Require a sample before a large purchase.
Clarify storage and transport conditions (temperature, moisture protection).
Request reference customer contacts and, if possible, photos/videos of production.
According to manufacturers, graphene oxide (GO) is a single- or few-layer oxidized graphene bearing oxygen-containing groups (epoxy, hydroxyl, carboxyl), hydrophilic, easily dispersible in polar solvents, and supplied as a powder or aqueous dispersion with a detailed CoA.
Manufacturer’s Description
Manufacturers describe GO as an oxidized form of graphene, where the underlying sp2 carbon network is covered with oxygen functional groups, giving the material a yellow-brown color, hydrophilicity, and high chemical reactivity. GO is typically offered as a powder, paste, or aqueous/organic dispersion; typical solvents are water, NMP, DMF, and THF.
Typical Technical Parameters per TDS
Manufacturers list a standard set of parameters in the TDS/CoA. Key fields and typical ranges (approximate values across different suppliers):
Elemental composition C/O: C ~45–75 at.%; O ~25–45 at.% (variation depends on the synthesis method).
Thickness/number of layers: single- or 1–4 layers; apparent thickness <5 nm.
Lateral size: 0.5–25 µm (depending on type and processing).
Appearance: yellow-brown powder or paste; dispersions — brown.
Solubility/dispersibility: disperses well in water and polar organic solvents.
BET surface area: for some products, ranges from ~5 to several hundred m²/g depending on type and processing.
Residual metals: manufacturers specify Mn, K, and other levels (ICP-MS) and permissible residue limits; laboratory grades have low values.
(Each item above is a typical parameter; specific numerical requirements depend on the grade and the manufacturer’s CoA.)
Supply Forms and Documentation
Manufacturers offer powder, pastes, and dispersions at specified concentrations; supply typically includes a Certificate of Analysis (CoA), FTIR/Raman/XPS spectra, TEM/SEM images, and SDS/MSDS. For biomedical applications, some suppliers provide endotoxin and basic cytotoxicity data on request.
Applications, Advantages, and Recommendations
GO is positioned as a convenient precursor for functionalization and production of rGO, ideal for membranes, composites, adsorbents, and biomedical platforms due to its abundance of functional groups and ease of solution processing. Manufacturers emphasize the need to request the full CoA and spectra for every batch and to test key parameters (C/O, ID/IG, sheet size, residual metals) before large-scale application.
In brief: Graphene oxide (GO) is an industrially viable material produced mainly by chemical oxidation of graphite (Hummers/modified Hummers/Tour), with real factory-scale technologies and suppliers operating at scale; the high price per kg is explained by reagent costs, energy intensity, waste treatment/disposal, and quality control.
1) Who Produces It and Commercial Status
Major suppliers and catalog vendors include ACS Material, Graphenea, and numerous Chinese and European manufacturers listed in industry reviews and supplier databases. Industrial plants exist (Abalonyx and others), along with pilot and commercial lines — the technology is not just a lab project but a real industrial supply chain with serial deliveries and CoAs.
2) Main Technologies (Real Protocols and Their Variations)
Hummers method (classic) — oxidation of graphite with KMnO₄ in concentrated H₂SO₄ (previously with NaNO₃), followed by exfoliation and washing; parameters control the degree of oxidation and defects.
Modified Hummers/Tour methods — eliminate NaNO₃, use H₃PO₄ or partially replace KMnO₄ with K₂FeO₄, and adjust acid ratios and temperature to increase yield and reduce by-products.
Alternatives: electrochemical oxidation, green methods (waste recycling) — at the research and pilot stage.
Practical parameters (typical, by manufacturer/protocol): concentrated H₂SO₄ (dominant by molar/volume ratio), KMnO₄ in excess (stoichiometry varies), reaction temperature usually 0–20°C during oxidizer addition, followed by heating to ~35–50°C for completion; subsequent treatment with water/peroxide and repeated washing to neutral pH; exact percentages and ratios depend on the method modification and raw materials.
3) Raw Materials and Key Inputs
Graphite (powder, flakes) — the quality of the starting graphite strongly affects sheet size and defects.
Reagents: concentrated H₂SO₄, KMnO₄ (or K₂FeO₄), H₂O₂/peroxide to reduce by-products; sometimes H₃PO₄; water for washing.
Equipment: cooled reactors, mixers, centrifuges/filters, drying ovens, wastewater treatment systems.
4) Why It’s Expensive — Cost Structure
Main cost items: raw material (graphite), chemicals (KMnO₄, concentrated H₂SO₄), energy-intensive processing and drying, treatment/neutralization and disposal of Mn waste, analytics/CoA, and packaging/logistics. Economic reports indicate that chemicals and waste treatment account for a significant share, along with capital costs for safe equipment and wastewater treatment systems.
5) Quality Control and Mandatory Tests
The CoA should include: XPS (C/O ratio), Raman (I_D/I_G), TEM/AFM (thickness, lateral size), ICP-MS (metal residues), TGA (moisture/thermal stability), FTIR, zeta potential, and BET (if needed) — these tests are critical for industrial use and affect the price and acceptability of the batch.
6) Risks and Recommendations for the Manufacturer
Environmental impact/disposal of Mn residues and acidic effluent is a key operational risk; invest in wastewater treatment.
Recipe optimization (modified methods, K₂FeO₄, H₃PO₄) can reduce KMnO₄ consumption and by-products, increasing yield and lowering CAPEX/OPEX.
Pilot line and CoA procedures: start with a pilot, require independent analytics for each batch, and optimize reagent ratios and temperatures for your graphite.
Comparison Table — Main Cost Drivers
General Scheme and Key Decisions
Method choice: Hummers/modified Hummers — simple and widely used; the Tour method gives a higher degree of oxidation and better exfoliation for certain feedstocks.
Raw materials: high-purity graphite (powder/flakes), concentrated H₂SO₄, KMnO₄ (or alternatives in modified versions), water, H₂O₂ for neutralization; sometimes H₃PO₄ in Tour variants.
Critical parameters: C/O ratio (XPS), I_D/I_G (Raman), lateral size (TEM/AFM), residual metals (ICP-MS) — require a CoA for every batch.
Step-by-Step Protocol — Classic (Hummers, Simplified)
Note: modifications (without NaNO₃, with H₃PO₄) reduce NOx emissions and ease purification; Tour variants use H₃PO₄/H₂SO₄ mixtures and yield a higher degree of oxidation.
(Table — brief summary; detailed masses/volumes scale linearly.)
Quality Control and Purification
Mn residue removal: thorough washing plus filtration; Mn control ≤ ppm by ICP-MS.
Analytics: XPS (C/O), Raman (I_D/I_G), TEM/AFM, TGA, FTIR, zeta potential — require spectra and raw data in the CoA.
Environment: neutralization of acidic effluent and manganese sludge is a significant OPEX item; industrial producers implement treatment and reagent-regeneration systems.
Why the Price Is High — Cost Structure
Chemicals (KMnO₄, concentrated H₂SO₄) and their consumption;
Effluent treatment/Mn waste disposal (regulatory and CAPEX/OPEX);
Energy (heating, drying, ultrasound);
Analytics and QA (XPS, TEM, ICP) for each batch;
Packaging/logistics and small market order volumes — all of this raises the price per kg.
Table: Main Synthesis Methods (Quick Overview)
Sources: .
Technological Details and Parameters (Additional)
Ratios: typical laboratory scale — graphite:H₂SO₄:KMnO₄ ≈ 1:23 mL:3–6 g (scalable); exact ratios depend on the modification and desired degree of oxidation.
Temperature profiles: KMnO₄ addition at 0–5°C, then holding at 30–50°C; the Tour method uses longer heating in the presence of H₃PO₄ for better intercalation.
Purification: repeated washing, centrifugation, H₂O₂ neutralization; ICP-MS Mn monitoring is mandatory.
Drying: vacuum/freeze-drying at <60°C to preserve structure.
(For exact mass ratios and volumes for your scale, a step-by-step recipe can be prepared calculated for a given throughput.)
Economics: Why the Price Is High
Chemical reagents (KMnO₄, concentrated H₂SO₄) and their consumption;
Wastewater treatment and Mn sludge disposal (significant OPEX/CAPEX);
QA/analytics (XPS, Raman, TEM, ICP) for each batch;
Energy and drying, packaging, and small sales volumes — all of this shapes the price per kg.
Risks and Practical Recommendations
Environmental risk: an effluent treatment system and reagent regeneration are mandatory; invest in Mn sludge treatment.
Feedstock quality: use graphite with controlled particle size and purity — this reduces defects and increases yield.
Optimization: test modified Hummers/Tour and electrochemical approaches at pilot scale; compare yield, C/O, and I_D/I_G.
Required analyses: a CoA with XPS (C/O), Raman (I_D/I_G), TEM/AFM, ICP-MS, TGA, and FTIR — require these for every batch.
In brief: feeding 1 t/h of thermally expanded graphite (TEGA) into the classic (or modified) graphene oxide process, you can expect a mass yield of GO ≈ 0.9–1.3 kg GO per 1 kg of starting graphite (weight increases due to added oxygen); typical laboratory recipes scale to tens of thousands of liters of acid and tons of oxidizer per hour, so the key tasks are reagent-ratio optimization, wastewater treatment (Mn sludge), and energy-efficient drying.
1. Expected Yield and Mass Balance (Guidelines)
GO yield: ~0.9–1.3 kg GO/1 kg graphite (variability depends on the degree of oxidation and removal of unmodified particles) — yield measurement requires a standardized methodology.
At 1 t/h of graphite, approximately 0.9–1.3 t/h of GO is produced (up to 31.2 t/day at 24-hour operation) — plan tanks and lines accounting for moisture and dispersion.
Methodology and yield discussion sources: Hummers/modified Hummers and studies on GO yield measurement.
2. Typical Reagents and Approximate Mass Requirements (Laboratory Recipe Scaled Up)
(original laboratory example: 1 g graphite : 23 mL H₂SO₄ : 3–6 g KMnO₄; scale linearly as a guideline.)
At 1 t/h graphite (approximately):
H₂SO₄ (conc.) ≈ 23 L/kg → ~23,000 L/h (23 m³/h) (laboratory guideline; optimized in industrial practice).
KMnO₄ ≈ 3–6 kg/kg → 3–6 t/h (modified variants reduce consumption).
H₂O₂/water for washing — tens of cubic meters of wash water per hour; centrifugation/filtration and neutralization are required.
Important: these figures are a direct scale-up of laboratory recipes; industrial practice uses optimization (Tour/modified Hummers) to reduce acid and KMnO₄ volumes.
3. Key Process Steps (Step-by-Step, Industrial Focus)
Loading graphite into a cooled acid reactor (0–5°C); dosing KMnO₄.
Controlled heating (up to ~30–50°C) to complete oxidation/exfoliation.
Quenching/desalting: adding water and H₂O₂ to reduce permanganate; formation of Mn sludge.
Repeated washing/filtration/centrifugation to neutral pH; ion removal (ICP-MS monitoring).
Exfoliation (ultrasound/mechanical) to obtain single-layer sheets.
Concentration and drying (vacuum, spray drying, or freeze-drying depending on the required form).
(Steps and parameters are discussed in detail in Hummers/Tour reviews and modifications.)
4. Main CAPEX/OPEX Drivers and Risks
Chemical reagents (KMnO₄, H₂SO₄) and their consumption; the cost of Mn sludge disposal and wastewater treatment is a major OPEX item.
Energy (heating, drying, ultrasound), filtration/centrifugation, analytics (XPS, Raman, ICP) — recurring costs.
Environmental and regulatory risks in handling concentrated acids and manganese waste; neutralization and disposal systems are required.
(Modified methods reduce reagent consumption and by-products — see improved protocols.)
5. Recommendations (for a TEGA Producer at 1 t/h)
Piloting: do not scale directly from the laboratory recipe — run a 1–10 kg/h pilot to optimize reagent ratios and washing.
Consider modified Hummers/Tour to reduce KMnO₄ use and improve yield; evaluate electrochemical methods as an alternative to reduce chemical reagent use.
Invest in effluent treatment and reagent regeneration (Mn sludge, neutralization).
Implement CoA procedures (XPS C/O, Raman I_D/I_G, TEM/AFM, ICP-MS) for every batch.
Consolidated Document on Graphene Oxide (GO)
Overview
Graphene oxide (GO) is a single- or few-layer carbon sheet with oxygen-containing functional groups: epoxy, hydroxyl, and carboxyl. These groups give the material hydrophilicity and high chemical reactivity, reduce electrical conductivity compared with pure graphene, and make GO a convenient precursor for functionalization and production of reduced graphene oxide (rGO). GO is supplied as a powder, paste, or dispersion in polar solvents.
Structure and Key Properties
Functional groups: epoxy –O–, hydroxyl –OH, carboxyl –COOH.
Thickness: on the order of a single carbon atom; typically one or a few layers.
Lateral size: from hundreds of nanometers to tens of micrometers, depending on the starting graphite and synthesis conditions.
Electrical conductivity: low for as-produced GO; increases after reduction (rGO).
Solubility: good dispersibility in water and polar organic solvents.
Mechanical properties: high strength, but lower than ideal graphene.
Appearance: yellow-brown powder or brown dispersion.
Synthesis Technologies and Step-by-Step Protocol
Main Methods
Classic Hummers — oxidation of graphite with potassium permanganate in concentrated sulfuric acid, followed by peroxide treatment and washing.
Modified Hummers and Tour — eliminate nitrates, introduce phosphoric acid or alternative oxidizers to reduce by-products and improve exfoliation.
Electrochemical and “green” methods — alternatives using fewer toxic reagents, often at the pilot stage.
Industrially Applicable Step-by-Step Protocol (Scheme)
Reactor preparation and graphite loading: loading graphite into a cooled reactor; maintaining temperature during oxidizer dosing.
Oxidizer addition: slow introduction of KMnO₄ (or alternatives) into concentrated H₂SO₄ at 0–5°C to control exothermicity.
Controlled heating: raising the temperature to ~30–50°C to complete oxidation and partial exfoliation.
Reaction quenching and permanganate reduction: dilution with cold water and addition of H₂O₂ until the purple color disappears; formation and removal of Mn sludge.
Washing and purification: repeated filtration/centrifugation and washing to neutral pH; removal of soluble ions and manganese residues.
Exfoliation: mechanical or ultrasonic delamination to obtain single-layer sheets.
Concentration and drying: vacuum drying, spray drying, or freeze-drying depending on the required product form.
Packaging and labeling: sealed packaging, batch labeling, and CoA preparation.
Typical Process Parameters
Temperature during oxidizer addition: 0–5°C.
Holding/heating temperature: 30–50°C (up to 60°C in modified variants).
Approximate ratios (laboratory scale): graphite:H₂SO₄:KMnO₄ ≈ 1:23 mL:3–6 g; scaling up requires optimization and reduction of acid and oxidizer volumes.
Wash water and H₂O₂ in large volumes for neutralization and removal of Mn residues.
Industrial Production at an Input Rate of 1 t/h of Thermally Expanded Graphite
Mass Balance and Yield
GO yield is approximately 0.9–1.3 kg GO per 1 kg of graphite, depending on the degree of oxidation and residual moisture; at 1 t/h of graphite, this is approximately 0.9–1.3 t/h of GO.
The mass balance must account for added oxygen, water in the dispersion, and losses during washing.
Approximate Reagent Requirements When Directly Scaling Up the Laboratory Recipe
Concentrated H₂SO₄: on the order of tens of cubic meters per hour under direct scale-up; industrially optimized and reduced.
KMnO₄: several tons per hour depending on the recipe; modifications reduce consumption.
Water and H₂O₂: large volumes for washing and neutralization.
Key Engineering Requirements
Reactors with effective cooling and mixers, reagent dosing systems.
Centrifuges, filters, and washing lines for sludge removal.
Drying systems (vacuum, spray dryers, freeze-dryers) depending on product form.
Wastewater treatment and manganese sludge disposal systems.
Quality control laboratory for regular batch analysis.
Quality Control and Documentation
Mandatory Analytical Tests for the CoA
XPS — elemental composition and C/O ratio.
Raman — I_D/I_G for defect assessment.
TEM/AFM — sheet thickness and lateral size.
ICP-MS — residual metals (Mn, K, Fe, etc.).
TGA — moisture content and thermal stability.
FTIR — confirmation of functional groups.
Zeta potential and DLS — dispersion stability.
BET — surface area, if needed.
Documentation and Batch Requirements
Certificate of Analysis with original spectra and raw data.
Batch/lot number and traceability of the starting graphite.
SDS/MSDS, storage conditions, and shelf life.
Batch sample for independent verification before a large purchase.
Economics, Environment, and Recommendations
Cost Structure
Main OPEX items: chemicals (KMnO₄, H₂SO₄), water and H₂O₂, energy (heating, drying, ultrasound), wastewater treatment and Mn sludge disposal, analytics and QA.
CAPEX: cooled reactors, filtration and centrifuge units, effluent treatment systems, drying equipment, and an analytical laboratory.
The price per kg of GO is high due to the combined costs of reagents, waste treatment, energy, and mandatory analytical batch testing.
Environmental and Regulatory Risks
Handling concentrated acids and manganese waste requires neutralization and disposal systems; non-compliance leads to fines and risks to personnel.
Biomedical applications require additional biocompatibility and toxicology testing.
Practical Recommendations for a Producer of Thermally Expanded Graphite at 1 t/h
Launch a pilot line (1–10 kg/h) to optimize the recipe and washing before scaling up.
Consider modified Hummers or the Tour method to reduce KMnO₄ consumption and by-products.
Evaluate electrochemical and “green” methods as potential ways to reduce environmental impact.
Invest in wastewater treatment and reagent regeneration systems to reduce OPEX and ensure regulatory compliance.
Implement strict CoA procedures and independent analytical verification of every batch.
Conclusion
Graphene oxide is an industrially viable material with a wide range of applications. Successfully scaling production from thermally expanded graphite to commercial GO at 1 t/h requires recipe optimization, significant investment in effluent treatment and analytical infrastructure, and process piloting. Adopting modified methods and reagent regeneration systems will reduce production costs and environmental risks, improving the product’s competitiveness.
In brief: single-layer GO is typically defined as a sheet with an “apparent” AFM thickness of ≈0.8–1.2 nm; if the share of sheets with >3 layers (by the chosen criterion) exceeds the allowed threshold in a batch, it is considered defective.
What Counts as a “Layer” and Why Measurements Exceed 0.34 nm
A single graphene atomic layer is theoretically ~0.34 nm, but for GO, due to oxygen groups, adsorbed water, and substrate interaction, the apparent AFM thickness is usually ≈0.8–1.2 nm for single-layer flakes.
Thickness criteria are therefore based on the AFM “apparent” value rather than the ideal 0.34 nm. This is confirmed by interlaboratory studies and review articles on characterization methods.
Practical Criteria (Recommended for QC, Based on Literature and Practice)
Single layer (1L): AFM ≤ 1.2 nm.
Two layers (2L): AFM ≈ 1.3–2.0 nm.
Three layers (3L): AFM ≈ 2.1–3.5 nm.
Multilayer (>3L): AFM > 3.5 nm — considered multilayer/undesirable for a “single-layer” product.
These ranges are practical guidelines; exact thresholds can be adjusted for your sample preparation method and substrate (Si/SiO₂ gives different readings than glass).
Recommended Measurement Methods and Controls
Sources: .
Batch Acceptance Criteria (Recommendation)
Statistics: measure ≥100–300 flakes by AFM using random sampling.
Tolerance: no more than 5% of flakes with >3 layers (AFM >3.5 nm) — otherwise the batch is rejected or requires reprocessing.
Report: include a thickness distribution (histogram), mean, median, and percentage of >3 layers; include example AFM scans and TEM images.
Practical Notes
Sample preparation is critical: drying, substrate (Si/SiO₂), AFM mode (tapping), and surface cleanliness all affect the readings.
Statistical representativeness matters more than a few “nice-looking” images — require a CoA with the layer distribution.
Use Raman and XPS as complementary methods to confirm chemistry and defect density, not as the sole criterion for layering.
If needed, a template CoA section on layering can be prepared (format: AFM methodology, number of samples, histogram, acceptance threshold) along with a sample report with charts.
Also published on: LinkedIn — Michael Vischmidt · Facebook — ARBOK Institute
