Industry generates used oil every single day. This has always been a cost item, tied to its removal and disposal. It’s the plant’s money, converted by inertia into waste status. First the oil is purchased, and prices for it have always been high. Then, once it’s spent its service life, its removal for disposal is paid for, along with the disposal itself. Then new oil is purchased. Three payments for the same volume. This triple billing rests on a single myth: that the oil ‘dies’ and can’t be restored. In practice, what degrades in oil are the contaminants, water, oxidation products, and maintenance discipline, while the base oil fraction in many cases remains practically unchanged. Ideally, then, the oil simply needs to be separated from everything that has contaminated it. That is exactly what ARBOK-ORR (Oil Regeneration & Return) is built on: not disposal, not ‘waste processing,’ but a full return of the oil to the working cycle using controlled phase-separation technology that removes everything that isn’t oil.
Let’s start with the types of oils.
Transformer dielectric oils and electrical equipment oils: mineral inhibited and bio-ester types. Their main enemies are water, gases, polar oxidation products, and solid particles, which kill breakdown voltage and accelerate paper aging. In this segment, the industry always lives by condition-based maintenance logic aligned with IEC approaches: not ‘drain and refill,’ but sustained parameters, since a transformer is an extremely expensive asset and the oil’s condition directly determines its service life. The next group is turbine and circulating oils, including bearing system oils, gearbox oils in adjacent units, and control hydraulic systems. Here the problem usually isn’t ‘chunks of dirt,’ but varnish deposits, sludge, microparticles, water, and oxidative degradation. The point of on-site regeneration is not to wait for a failure and perform a heroic ‘full drain,’ but to keep the oil in condition continuously.
Internal combustion engine oils. A tough category. Beyond solid particles, engine oil carries chemistry: soot, nitration, oxidation, fuel, sometimes glycol, plus depleted additives. Removing only the solid phase genuinely improves wear and cleanliness, but doesn’t return the oil to ‘like new.’ Adding dehydration and fuel control can double the drain intervals across a fleet; ideally, dosing the additive package as well — which is just normal engineering, without the cult of ‘drain and replace everything on a fixed calendar.’
There are other types of used oils where regeneration makes sense, though not always on-site. Compressor and vacuum oils often respond well to dehydration and servicing. Gear oils — provided there’s no heavy metal contamination and the EP additives remain intact. Heat-transfer fluids and thermal oils are serviced with mandatory analysis of degradation and fractional composition. Greases, coolant emulsions, and ‘oil that’s really soup with water’ are a separate story: a mobile system either becomes a mini-plant or honestly routes the stream to stationary processing. There are also stop-categories: PCB-contaminated dielectrics and undefined mixtures. These can’t be ‘nicely regenerated’ while pretending everything is legal and safe.
Now, about ARBOK-ORR and the claim that ‘Arbok just removes solids.’ For transformer and turbine oils that description is too modest: water and gases aren’t ‘solids,’ yet they do more damage than metal shavings. But even within the ‘solids only’ framing there’s an effect: abrasive wear drops sharply, the oxidation rate at contamination centers falls, and sludge growth stops. In the engine-oil segment, ‘solids only’ delivers less, but it still generates money, because wear and downtime cost money. This is where the right product architecture begins: a base ‘solids’ mode as the minimal module with fast ROI, followed by modes where water and gases are critical (transformers, turbines, hydraulic systems), because that’s where the failures and the big bills are concentrated. This isn’t a fairy tale about ‘eternal oil’ — it’s about stopping the practice of hauling away an asset as garbage just because foreign phases have accumulated in it.
But back to the ARBOK-ORR technology itself. Oil is a base hydrocarbon phase. During operation it picks up water, gases, volatile components, and heavy degraded fractions, along with solid contaminants, chips, shavings, and dust. Arbok-Evaporation technology uses deep vacuum, under which water and light contaminants evaporate out of the oil phase without damaging the base, while heavy degraded fractions and solid contaminants are collected in a separate concentrate. This isn’t ordinary filtration — it’s the separation from the oil of everything that prevents it from doing its job. The result is two output streams: clean oil that meets specifications and is functionally indistinguishable from the original product, and a contamination concentrate: water, oxidation products, varnish masses, sludge, metal particles (Fe, Cu, Al), scale, quartz dust (SiO₂), soot, calcium and magnesium compounds, and other inclusions picked up by the system during real operation. These contaminants make up a small volume — roughly 3–5% — which genuinely needs disposal. That volume has to be replaced with a top-up of new oil, but it’s only 3–5%, not 100%. This is where the economic effect comes from, plus logistics savings: no more hauling tons of new oil in and the same volume of ‘dirty’ oil out as waste; instead, only kilograms of concentrate leave the site, and the fresh top-up covers only the irreversible losses.
Solid residues after ARBOK-ORR are a concentrate of problems, not ‘used oil’: wear metals, sludge, varnish masses, abrasive dust, carbonaceous inclusions, and a separated water phase. Only a small fraction of the concentrate is disposed of, not the entire oil volume. The economics of handling it change radically. The solid residues after the technology come out as plain water, plus paste-like waste amounting to roughly 3–5% of the volume of oil being treated. These wastes are disposed of by standard means, and their volume is small enough not to be a problem.
The economics of oil regeneration are substantial: buying new oil at market price, holding ‘just in case’ stock as frozen capital, collection, transport, and disposal, sometimes ‘paperwork.’ In field practice, disposal rates for used oil run around $3.5/gal, equal to $0.925/L or $925/m³. Adding even $0.20/L for logistics and paperwork brings the real cost of ‘getting rid of a liter’ to $1.125/L or $1,125/m³. At this point the debate over whether regeneration makes sense is over — all that’s left is arithmetic.
New oil prices confirm the scale. Transformer oils run around $3.5–4.5/L; engine oils are 30–60% more expensive depending on the grade; aviation fluids run around $25–30/L, and hydraulic fluids $45–50/L. Against this backdrop, regeneration becomes a source of major savings, and therefore of earnings.
The ARBOK-ORR unit uses no filters, membranes, anodes/cathodes, inhibitors, coagulants or flocculants, cavitation, plasma, or any other consumables in its operation. Nothing except 0.7 kWh/t of electricity. Unit throughput can be anything — from 5 liters to 200 tons per hour. The base configuration, with a capacity of up to 200 tons of oil per day, is a vertical column-type apparatus (roughly 20 feet) with a discharge and packaging unit for the contamination concentrate.
For convenience, ARBOK-ORR can be mounted on a truck chassis and provide oil regeneration services directly on-site. In this case, purchasing equipment isn’t necessary, and payment is made for the regeneration result. For sites with confidentiality restrictions, or for large vessels and port operations, a stationary version is more commonly used, where the effect stays the same but the ownership model changes.
Because of the simplicity of the process cycle and the absence of heating (the process runs at ambient temperature), the cost of regeneration work is minimal. Depending on the oil type, regeneration costs range from 15 to 25% of the cost of a full replacement. As a result, ARBOK-ORR delivers up to 75–85% economic benefit compared to the ‘drain-haul-buy’ scenario.
The number of regeneration cycles for oils is large. Transformer oil can be serviced repeatedly — as many times as the equipment lasts — with periodic replacement of 3–5% of the volume. Around 14–23 cycles pass before half the volume is renewed. For engine oils, it’s more accurate to talk about reduced purchasing: minus 40–60% while maintaining condition.
Below is a summary table capturing exactly what’s described above in words: what volume of oil passes through ORR at typical sites, which oil group dominates, and what order of net savings forms at current prices for new oil and disposal, including the real tariff of $1.125/L for ‘getting rid of a liter.’
Table. ARBOK-ORR Economics for Typical Sites (Summary)
(results in USD; disposal accounted for at $1.125/L = $1,125/m³)
Time is the most underrated factor. On-site or stationary regeneration cuts downtime, waiting for collectors, and operational hassle. In emergency scenarios, the cost of a day of downtime multiplies far beyond the cost of the liters of oil involved.
In the industry, oils are usually ‘cleaned,’ not regenerated. Mechanical filters and cartridges remove only solids and become consumables themselves; centrifuges separate the heavy phase and free water but leave dissolved moisture, gases, and oxidized chemistry untouched; classic vacuum dehydrators dry the oil without addressing heavy degradation; sorption columns temporarily capture polar aging products but have a limited service life, require replacement, carry off additives, and become waste themselves; refinery-based reprocessing moves the process into oil refining entirely, with logistics, CAPEX, and disposal. ARBOK-ORR works differently: it doesn’t filter the oil or ‘treat’ it with additives — through Arbok-Evaporation it physically separates the phases. Water, gases, volatile and degraded fractions leave the oil medium as distinct entities, solid contaminants are concentrated, and the base oil fraction returns to the cycle. The difference is fundamental: conventional methods try to improve the oil within a single phase, while ARBOK separates out of it everything that has stopped being oil, reducing waste volume and returning the asset to work.
The technology delivers a substantial economic result at a global scale. The following table shows the order of magnitude of savings by region under mass deployment of ARBOK-ORR: this isn’t a ‘market estimate’ but an estimate of the money currently spent buying new oil and disposing of the old, which returns to the enterprise economy as a net effect.
Macroeconomic Effect (Order of Magnitude)
Bottom line. ARBOK-ORR completely changes the rules of the game: oil is an asset, and a prudent owner doesn’t throw an asset away because it got contaminated — they return it to work. 3–5% concentrate versus a 100% drain. The economics rest not on slogans but on a direct reduction in new-oil purchases, a reduction in disposal volume, reduced logistics, and lower downtime risk. Where confidentiality and perimeter security matter, stationary units are used; where speed and service matter, the mobile version works. The point of the technology is one: the oil goes back into the cycle, and only the concentrate of the causes of degradation is hauled away — not the asset itself. ARBOK-ORR technology is for those who know how to count profit and aren’t willing to pay three times for the same liter.
Also published on: LinkedIn — Michael Vischmidt · Facebook — ARBOK Institute
