Post

TIN. All of electronics rests on it, and it goes down the drain.

❌ The fact: tin is lost neither in the mine nor in the bath. It is lost in the rinse. A part leaves the tinning bath with a film of solution on it: drag-out, 0.1–2 litres…

❌ The fact: tin is lost neither in the mine nor in the bath. It is lost in the rinse.

A part leaves the tinning bath with a film of solution on it: drag-out, 0.1–2 litres per m². At 30–60 g/L of tin in the bath, that is 3–120 grams off every square metre treated. Rinsing it clean dilutes that drag-out 500–1,000 times, and the tin ends up smeared across an enormous volume of water: 10–500 mg/L.

Drag-out is the main loss channel of a plating bath: everything the shop tops it up with, beyond what plated onto the part, went into the rinse. The spent bath is regenerated; the rinse water nobody regenerates. It goes to lime-and-caustic treatment and becomes hydroxide sludge classified as hazardous: the shop buys reagents and equipment to turn its own tin into toxic waste, then pays fines to discharge it. Tin is paid for twice: bought first, buried after.

❌ The numbers:

  • Tin: $56,000/t (2026), +66% in a year
  • World refined production ~380,000 t/year; deficit from 2026, first since 2021
  • China ~30% of mining and half of world refining; Indonesia second and falling
  • DR Congo and Myanmar: 20% of world production, 60% of China’s ore imports
  • Reserve life ~15 years, the worst of any industrial metal
  • Half of demand is solder; AI-server demand forecast to triple by 2030

🟢 ARBOK-ZWD takes tin from where it is drowned today.

1 — Rinse waters of tinning and plating lines: tinplate, connectors, leadframes

2 — PCB effluent: spent tin strippers and the rinses after them

3 — Semiconductor etch and rinse lines (tin bumps)

4 — E-waste leachates

🟢 ZERO WASTE DISCHARGE.

We do not change the shop’s chemistry. We remove the volume problem.

  • deep-vacuum separation at ambient temperature
  • 100% of volume back as clean water, zero discharge
  • ballast — acids, salts, companion metals — as dry fractions
  • tin concentrates separately, into the shop’s own electrowinning
  • No membranes, no reagents, no consumables. Under 1 kWh/m³. That is all.

🟢 Economics of one unit:

  • Arbok unit: 20-ft container, 200 m³/day = 73,000 m³/year
  • An average PCB plant discharges 500–2,000 m³/day: 3–10 units
  • Tin at 10–500 mg/L = 0.7–36.5 t a year = $41,000–2,000,000
  • Typical case, 50 mg/L: 3.7 t = ~$205,000
  • Water: 73,000 m³ not bought and not discharged = $150,000–360,000
  • Sludge: 36–146 t/year of hazardous waste never forms = $22,000–230,000

TOTAL per unit: $250,000–1,000,000 a year. Typical case about $500,000.

🟢 Who needs it: PCB plants in China, Taiwan, Korea, Vietnam, Thailand; tinplate mills; semiconductor fabs; anyone who must prove tin origin under 3TG or EU 2017/821.

🟢 Bottom line: tin has not run out. It is being thrown away.

Already mined in Myanmar or Congo, already dissolved in your bath. From there it goes into the rinse and becomes hazardous sludge you pay for twice. And it is the only tin in the world whose origin you can prove: the path from bath to ingot is 1 metre.

@Arbok #Tin #CriticalMinerals #ZWD